Elmomc SimplIQ Command Reference Manual do Utilizador Página 93
- Página / 188
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
KL - Kill Motion and Program
Purpose:
Halts program execution and stops the motor. The KL command stops the execution of
the user program threads and automatic routines. It also issues the MO=0 motor disable
command. KL freezes the status of the program and does not reset it. A later XC
command will resume the program from the instruction at which the program was
halted. Pending interrupts will remain pending.
A KL command issued when no program is running does nothing, and sets no error
code.
Attributes: Type: Command, No value
Source: RS-232, CANopen
Restrictions: None
Unit modes: All
Activation: Immediate
If the motor is on when KL is used, using XC to continue the program may fail,
because the interrupted program expects the motor to be on, and it may use
commands that are restricted to the MO=1 state.
See also:
HP, XQ, XC
SimplIQ Command Reference Manual Alphabetical Listing
MAN-SIMCR (Ver. 4.5)
3-80
- SimplIQ 1
- Important Notice 2
- Contents 3
- Chapter 1: Introduction 6
- 1.2 Scope 7
- MAN-SIMCR (Ver. 4.5) 10
- Command Reference Manual 14
- Limit Ranges 16
- (Single_Turn+Multi_Turn) 17
- AC - Acceleration 19
- AG[N] - Analog Gains Array 20
- AN[N] - Analog Inputs Array 21
- SimplIQ electronics 22
- BG - Begin Motion 23
- BP[N] - Brake Parameter 25
- CA[N] - Commutation Array 28
- 16 - CA[34] 30
- 16-CA[34] 33
- CC - Compiled Program Ready 34
- CD - CPU Dump 35
- SimplIQ Software 37
- CP - Clear Program 39
- DC - Deceleration 40
- DD - CAN Controller Status 41
- DF/DS - Download Firmware 42
- DL - Download Program 43
- EC - Error Code 45
- SimplIQ internal use 53
- SimplIQ drive internal use 53
- EM[N] - ECAM Parameters 60
- EO - Echo Mode 62
- FF[N] - Feed Forward 65
- FR[N] - Follower Ratio 66
- GS[N] - Gain Scheduling 67
- SimplIQ can: 70
- HP - Halt Program Execution 73
- HX - Hexadecimal Mode 74
- IB[N] - Input Bits Array 78
- IF[N] - Digital Input Filter 80
- IL[N] - Input Logic 81
- SimplIQ drive will retry 82
- Harmonica drive has 6 86
- IP - Input Port 88
- JV- Jogging Velocity 90
- KI[N], KP[N] - PI Parameters 92
- KL - Kill Motion and Program 93
- LC - Current Limit Flag 95
- LL[N] - Low Feedback Limit 97
- LP[N] - List Properties 98
- LS - List User Program 99
- MF - Motor Failure 101
- MI - Mask Interrupt 104
- SimplIQ Software Manual: 105
- MO - Motor Enable/Disable 106
- MS - Motion Status 110
- OB[N] - Output Bits Array 111
- OC[N] – Output Compare 113
- OC[3]=100(RS), volatile 115
- OC[4]=200(RS), volatile 115
- OL[N] - Output Logic 116
- drive will receive 117
- OP - Output Port 118
- PA - Absolute Position 119
- PE - Position Error 120
- PK - Peak Memory 121
- SimplIQ Software Manual 122
- PM - Profiler Mode 124
- PP[N] - Protocol Parameters 125
- PR - Relative Position 127
- PS - Program Status 128
- PT - Position Time Command 129
- Notes: 131
- PX - Main Position 132
- PY - Auxiliary Position 133
- RG - Recorder Gap 136
- RL - Record Length 137
- RM - Reference Mode 138
- RP[N] - Recorder Parameters 139
- RS - Soft Reset 142
- RV[N] - Recorded Variables 143
- SD - Stop Deceleration 144
- SF - Smooth Factor 145
- SN - Serial Number 146
- SP - Speed for PTP Mode 147
- SR - Status Register 148
- ST - Stop Motion 150
- TC - Torque Command 152
- TM - System Time 154
- TR - Target Radius 156
- TS - Sampling Time 157
- TW[N] - Wizard Command 158
- UF[N] – User Float Array 159
- UI[N] – User Integer 160
- UM - Unit Mode 161
- VE - Velocity Error 163
- VR - Firmware Version 165
- 3-50 below 168
- 3-52 below 169
- 3-53 below 169
- XM[N] - X Modulo 175
- XP[N] - Extra Parameters 176
- YM[N] - Y Modulo 180
- Storage 182
- array · 3-9 183
Manuais e produtos relacionados com Hardware Elmomc SimplIQ Command Reference
Hardware Elmomc SimplIQ Digital Servo Drives-Guitar Installation G Manual do Utilizador
(76 páginas)
(76 páginas)
Hardware Elmomc SimplIQ Digital Servo Drives-Solo Guitar ABS Cable Manual do Utilizador
(13 páginas)
(13 páginas)
Hardware Elmomc SimplIQ Digital Servo Drives-Solo Guitar Installat Manual do Utilizador
(73 páginas)
(73 páginas)
Hardware Elmomc SimplIQ Digital Servo Drives-Solo Guitar ABS Insta Manual do Utilizador
(64 páginas)
(64 páginas)
Hardware Elmomc SimplIQ Analog Servo Amplifiers-Ocarina Installati Manual do Utilizador
(30 páginas)
(30 páginas)
Hardware Elmomc SimplIQ Analog Servo Amplifiers-Ocarina Evaluation Manual do Utilizador
(31 páginas)
(31 páginas)
Hardware Elmomc SimplIQ Analog Servo Amplifiers-Violin Installatio Manual do Utilizador
(23 páginas)
(23 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.022 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais